martino communications
about the agency
client portraits
client list


home > news > details


Nordson BKG® HiCon™ V-Type 3G with Power Backflush Technology Keeps Flow and Pressure Constant, Even While Removing Heavy Contaminants

MÜNSTER, GERMANY, September 2, 2016: Nordson Corporation has enhanced the design of its patented “power backflush” V-Type screen changer, creating a more compact and efficient system whose continuous operation eliminates downtime in extrusion, pelletizing, and recycling.

Nordson’s BKG® HiCon™ V-Type 3G screen changer uses a hydraulically powered backflush system to automatically remove contaminant while maintaining extrusion throughput and keeping flow and pressure constant. Operationally, the new screen changer is more streamlined and efficient than the earlier V-Type system from Nordson, with a 30% shorter backflush cycle. There is a higher degree of automation resulting from an autonomous parameterizing of the entire backflush procedure and of the screen change procedure, including filling and venting.

All of the filtration area of the combined four screen cavities is available for production while filling of the displacement-piston cylinder takes place. Two outlets for backflushed material are located on the bottom of the unit, with discharge automatically controlled by the movement of the screen-bearing pistons.

In comparison with the earlier V-Type system, the height of the new V-Type 3G screen changer has been reduced by 30%, permitting a lower extrusion height; a single displacement piston is used for backflushing instead of having one for each screen cavity; and hydraulic piping has been optimized.

“The HiCon V-Type 3G screen changer provides up to 200 backflushing cycles before screens must be changed, reducing operating costs,” said Christian Schroeder, global product manager for melt delivery products. “With four screen cavities making a large filtration area available in a comparatively small housing, only minimal amounts of material are lost in backflushing.”

In the HiCon V-Type 3G screen changer, melt flow from the extruder is split at the entry side and guided to the four screen cavities, two of which are located on each piston. Each pair of cavities is positioned so that they can filter their respective melt streams, until the piston removes one of the cavities from the process to remove contaminant buildup by means of backflushing. In normal operation, polymer is flowing through all four cavities. While one of the cavities is changed, the other three remain in the process.

In addition to the two screen-bearing pistons, there is a single hydraulically actuated displacement piston that operates during backflushing. When the differential pressure across the screen changer increases to a pre-set level because of contaminant buildup, the backflush sequence for all cavities will be started automatically. For each cavity, the displacement piston retracts, creating a reservoir of filtered molten polymer. This material is hydraulically compressed and discharged in reverse direction, back through the screen, carrying away contaminant for removal from the system. The sequence is performed for each cavity one after the other.

“Our new backflush screen changer is suitable for almost all processes and materials,” said Mr. Schroeder, “including processes with strict requirements for constant pressure, such as strapping, film, fiber, and processes with insufficient back pressure for backflushing, such as strand pelletizing. It is also well suited for PET recycling material with a high proportion of contaminants.”


Nordson Corporation engineers, manufactures and markets differentiated products and systems used for the precision dispensing of adhesives, coatings, sealants, biomaterials, polymers, plastics and other materials, fluid management, test and inspection, UV curing and plasma surface treatment, all supported by application expertise and direct global sales and service. Nordson serves a wide variety of consumer non-durable, durable and technology end markets including packaging, nonwovens, electronics, medical, appliances, energy, transportation, construction, and general product assembly and finishing. Founded in 1954 and headquartered in Westlake, Ohio, the company has operations and support offices in more than 30 countries. Visit Nordson on the web at, @Nordson_Corp, or

Nordson Polymer Processing Systems provides customers with engineered components to melt, homogenize, filter, meter, and give shape to plastic and fluid coating materials. Nordson Corporation leverages the collective plastics industry experience from a series of strategic acquisitions to offer a uniquely broad portfolio of industry-leading technologies. Nordson delivers a full range of precision melt stream products — from screws and barrels for extrusion and injection molding — to filtration systems, pumps, and valves — to the extrusion dies and pelletizing systems to meet the constantly evolving needs of the polymer industry.

Nordson Corporation provides customers with local technical sales, service and remanufacturing capabilities through sales organizations and regional manufacturing facilities in over 30 countries. To learn more visit us at or